Huawei HG530 Instrukcja Użytkownika

HUAWEI HG530 Home Gateway User Guide

8 2. Install and configure the PPP dial-up software on your computer. The PPP dial-up software is pre-installed on certain computer operating system

9 4 Configuring the Wireless Network Connection If a wireless network adapter is installed on your computer, you can connect you computer to the HG53

10 1) Right-click My Computer, and then choose Manage from the shortcut menu. 2) In the Computer Management window, choose Computer Management (L

11 5 Configuring the Device 5.1 Changing the Administrator Password Used for Logging In to the Web-Based Configuration Utility For safety reasons or

12 5.2 Enabling or Disabling the Wireless Network Function You can quickly enable or disable the wireless network function by pressing the WLAN butto

13 5.4 Changing the IP Address Used for Logging In to the Web-Based Configuration Utility To make the login IP address easy to remember, you can chan

14 After the preceding operations, the current page jumps to the login page. You can log in to the Web-based configuration utility by entering the de

15 6 FAQs Can I use the terminal as a DHCP server? Yes, you can. The terminal incorporates the DHCP server software. How can I quickly restore the de

16 1) In IP address, enter 192.168.1.100. Ensure that this IP address is unique and not used by other computers. 2) In Subnet mask, enter 255.255.

17 3) Replace telephone lines. If the ADSL indicator still blinks, contact your network service provider. 3. Check whether the LAN indicator of the

i Contents 1 Warnings and Precautions ... 1 2 Connecting the Cables and Getting Started ...

18 2) Restore the default settings of the terminal. If the problem persists, contact your network service provider. 7. Check whether the proxy serv

19 If the driver is improperly installed, install it properly. 5. Check whether the computer can receive the signals of a WLAN. Take a computer that

20 If your computer is far from your terminal, the effects of the WLAN are affected. 4. Place your terminal and computer in another direction. 5. D

21 5. If the problem persists, restore the default settings of the terminal. What can I do if Web pages often cannot be displayed during Web page br

22 7 Appendix 7.1 Indicators Indicator Status Description Power On The HG530 is powered on. Off The HG530 is powered off. ADSL Blinking The

23 Indicator Status Description LAN1 - LAN4 Blinking Data is being transmitted through the Ethernet interface. On The Ethernet connection is set

24 Number Interface or Button Description 4 Reset You can press and hold the Reset button for over six seconds to restore the default settings of

25 Item Specification Relative humidity for operation 5% to 95%, non-condensing Dimensions (L × W × H) 156.4 mm × 52 mm × 124.3 mm Weight About 245

26 Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved. No part of this document may be reproduced or transmitted in any form or by a

27 TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO CASE SHALL HUAWEI TECHNOLOGIES CO., LTD BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT,

1 1 Warnings and Precautions To use the device properly and safely, read these warnings and precautions carefully and strictly observe them during op

2 device immediately, power it off, remove all the cables connected to it, and then contact an authorized service center.  During thunderstorms, po

3  Ensure that the power adapter meets the requirements of Clause 2.5 in IEC60950-1/EN60950-1 and it is tested and approved according to national o

4 2 Connecting the Cables and Getting Started Thank you for purchasing the HUAWEI HG530 Home Gateway (hereinafter referred to as the HG530). 2.1 Conn

5 After you power on the HG530, the ADSL indicator blinks (for less than three minutes), which indicates that the HG530 is being activated. After the

6 3 Setting the Network-Access Parameters By configuring the HG530 and your computer, you can choose any of the following methods to surf the Interne

7 2) Select a PVC number, such as 1, from the PVC drop-down combo box. 3) Enter the VPI and VCI that are provided by the network operator in the VP